Difference between revisions of "Laser"

Revision as of 17:30, 28 February 2022

The Laser Engraver/Cutter Area at Pikes Peak Makerspace (PPM) consists mostly of Level 3 equipment.

Additional training is required to use our Level 3 equipment. Laser Area hand tools should be marked with red tape or paint.

stuff

BOSS LASER area

Safety First

Members must know the following information:

In case of emergency, call 911.

Our physical location is:

735 East Pikes Peak Avenue

Colorado Springs, CO 80903

use this when ordering pizza or an ambulance

IN CASE OF
EMERGENCY
sign

PPM Fire Escape Plan

Fire Escape Plan maps are posted throughout the Makerspace.

There are 7 fire extinguishers on the fire escape plan map. Review the PPM Fire Escape Plan for locations.

PPM Emergency
Evacuation Plan.pdf
PPM Fire
Prevention Plan.pdf
PPM Fire Escape
Plan

First Aid

There is a FIRST AID Supply Cabinet in our Kitchen Area.

FIRST AID Kits are available in four areas: the Kitchen, Metal Shop, Wood Shop and CNC Room.

FIRST AID
Supply Cabinet
FIRST AID
Kit

Eye Wash Stations

Emergency Eye & Face Wash Stations are mounted in four areas: the Kitchen, Wood Shop, CNC Room and Vented Room.

Emergency
Eye & Face Wash
Station

Personal Protective Equipment (PPE)

Wear protective equipment in all Wood and Metal Shop Areas.

Wear gloves when using Isopropyl Alcohol and other cleaners.

Personal Protective Equipment (PPE)

Hazardous Chemicals

All hazardous chemicals must be stored in the yellow hazardous chemical storage cabinet located in the Vented Room.

Review the Safety Data Sheet (SDS) information of unknown products before use.

SDS information is available via the QR code on the hazardous chemical storage cabinet or this spreadsheet.

Do not bring dangerous chemicals to the makerspace.

Spray paint, stains, and other approved items must be stored in the hazardous chemical storage cabinet in the Vented Room.

Please DO NOT paint indoors.

Flammables Cabinet
in the Vented Room

Impairment

The use of PPM equipment requires you to be alert, attentive, and focused.

Do not use any PPM work area, or any PPM tools, if you are under the influence of drugs or alcohol.

Classes and Training

Area Captains

Robbie Cochran (Epilog Laser)

Lisa MacNicol (BOSSLASER)

Area Captain Duties

Classes

Pikes Peak Makerspace announces its Upcoming events, including classes, on Meetup

Training

Robbie Cochran (Epilog Laser)

Nicolas Ordahl (BOSSLASER)

Watch these videos on LightBurn BEFORE (BOSSLASER) CLASS!

Lesson 1 First Time User

Lesson 2 LightBurn UI Walkthrough

Lesson 3 Cut Settings

LightBurn Basics #1 Importing, Selection, Grouping, Movement

LightBurn Basics #2 Text and Offsetting

LightBurn Basics # 3 Trace Image and Weld

Pikes Peak Makerspace Boss Laser Intro -- external link to PPM YouTube channel

ALWAYS ensure the work area interior and exterior is clean before and after your work.

Boss Laser Orientation class handout
LIGHTBURN
HotKey List

Tips

DO NOT cut materials with PVC on either laser, this will release chlorine gas which is toxic.

For Help

Message in PPM Slack channel #laser-cutter

The following pages contain historical information. The pages are provided for reference only.

• Introduction to the Zing Laser‏‎ (15:26, 20 May 2015)

• Laser Cutting Material Table‏‎ (15:41, 21 May 2015)

• Laser Cutting Acrylic‏‎ (16:31, 24 November 2015)

Equipment Lists

BOSSLASER

Picture	Item	Manufacturer	Model Number	Estimated Value	Manual	Owner	Status	Problem Description
	Boss 150 Watt CO₂ Laser	Boss	LS-3655	$20,000	Operators Manual	PPM	working (12/28/21)
	OUTFEED TABLE	Mike Mike				PPM	working (12/28/21)
	Industrial Chiller	S&A	CW‑5000DG		Maintenance Manual	PPM	working (12/28/21)
	Compressor					PPM	being repaired (01/22/22)
	Computer	HP	h8-1117c	$250		PPM	working (12/28/21)
	27" Monitor	Dell		$100		PPM	working (12/28/21)
	rotary attachment for Boss Laser					PPM	?
Picture	Item	Manufacturer	Model Number	Estimated Value	Manual	Owner	Status	Problem Description

Zing LASER

Picture	Item	Manufacturer	Model Number	Estimated Value	Manual	Owner	Status	Problem Description
	Zing 30 Watt Laser	Epilog Laser	10000 Laser System	$5,800	yes, and online	PPM	working
	Computer	HP	h8-1117c	$250		PPM	working
	20" Monitor	Dell		$100		PPM	working
Picture	Item	Manufacturer	Model Number	Estimated Value	Manual	Owner	Status	Problem Description

Hand Tools

Laser Area hand tools should be marked with red tape or paint.

Return all tools to their proper location after use. This rule applies to all areas of our Makerspace.

Donations Received

Wish List

Policies

Equipment Reservations

Materials

DO NOT cut materials with PVC on either laser, this will release chlorine gas which is toxic.

Donate for "Wood Sheet for Laser" via PayPal: bit.ly/ppmstuff

Or, leave donations in a black payment box, or use a QR code.

Help Us Keep Stocked Up!

PPM members enjoy discounts at the following local merchants:

(bring proof of membership)


Company	Website	Benefit	Directions to
	Woodcraft of Colorado Springs	10% discount	4438 Austin Bluffs Parkway
	CO Lumber Specialties	10% discount	3636 Stone Avenue
	GENERAL AIR	10% discount	3031 N Nevada Ave.
	ACE Hardware Uintah Gardens	10% discount	1830 W Uintah Street

Map of stores that provide PPM member discounts

Map of helpful local resources curated by our makers

At home LightBurn subscriptions can be purchased at a discounted rate for being a PPM member.

The discount code is saved as a Pinned Message in our 'laser-cutter' channel in Slack.

Scrap and Trash

Trash day is MONDAY

Recycling day is MONDAY (96 gallon tote)

Single Stream Recycling provided by Waste Connections. Paper, cardboard, cans, glass, and one time use plastics.

Empty recycling and trash into our dumpster at the back (south side) of the building.

Always leave the space better than you found it.

Software

Design Software

Adobe Illustrator (Windows 10 and Macintosh)

Adobe Photoshop (Windows 10 and Macintosh)

Inkscape Tips

Procreate (Tips, Training and Meetups)

Printing Software

LightBurn (for BOSSLASER)

Adobe Acrobat (for Epilog LASER)

Member Showcase

Boss Laser Photo Gallery

4' x 1' Wall art
with inlays
(by Robbie Cochran)
Wall art with inlays.jpg

4' x 1' Wall art
with inlays
(by Robbie Cochran)
Laser engraved panels
(by Mike Mike)
Wall art princess bride.jpg

princess bride
minimalist wall art
(by Ben Severson)
Wall art INGLOURIOUS BASTERDS.jpg

INGLOURIOUS BASTERDS
minimalist wall art
(by Ben Severson)
THE IRON GIANT
minimalist wall art
14"x24"
THE IRON GIANT
(by Ben Severson)
THE IRON GIANT
(by Ben Severson)
TOSC tour
2021-11-24

Epilog Laser Photo Gallery

TOSC tour
2021-11-24
Laser cut
wooden clock
(Trevor Banks)
Round PCB
PPM clock
PPM engraved PCB keychain
3" engraved wooden keychains
PPM Library
engraved metal sign
Light switch cover
Manitou Art Center
Minnesota NICE
Manitou Art Center
(May 29, 2015)
Intro to Laser Cutting
Manitou Art Center
(January 15, 2015)

PPM YouTube Channel

"featured" videos, (the YouTube "HOME" tab)

"Things we've built", Created playlists, including 3D-printed robotic hand (2015)

Other Fun Stuff

Cut boxes with a laser cutter: MakerCase or Boxes.py

What is an ambigram?

Procreate superpowers

Search the PPM Wiki — include Content pages as well as Multimedia.

Contact Us if you cannot find your answer here on our Wiki or if you notice any information that is outdated.

@@ Line 5: / Line 5: @@
 Additional training is required to use our Level&nbsp;3 equipment.
 <span style="color:#FFFFFF; background:#D81F2B">&nbsp;Laser Area&nbsp;</span> [[Laser#Hand Tools|hand tools]] should be marked with <span style="color:#D81F2B">'''red'''</span> tape or paint.
+<br>
+<br>
+stuff
 <br>
 <br>
@@ Line 20: / Line 23: @@
 ===[[Area Captain Duties#Laser|Area Captain Duties]]===
 ===Classes===
-: Pikes Peak Makerspace announces its  [https://www.meetup.com/pikespeakmakerspace/events '''Upcoming events, including classes, on Meetup''']
+:Pikes Peak Makerspace announces its  [https://www.meetup.com/pikespeakmakerspace/events '''Upcoming events, including classes, on Meetup''']
 ===Training===
@@ Line 44: / Line 47: @@
 ===Tips===
 :'''DO NOT cut materials with PVC on either laser,''' this will release chlorine gas which is toxic.
-===For Help===
+===For Help ===
 :Message in PPM Slack channel #laser-cutter
 <br>
@@ Line 109: / Line 112: @@
 |
 |PPM
-| being repaired
+|being repaired
 (01/22/22)
 |
@@ Line 115: / Line 118: @@
 |[[File:BOSS LASER Computer.jpg|alt=BOSS LASER Computer|center|frameless|150x150px]]
 |'''Computer'''
-|HP
+| HP
 |h8-1117c
 |<p style="text-align:right;">$250</p>
@@ Line 154: / Line 157: @@
 |}
-===Zing LASER===
+=== Zing LASER===
 {| class="wikitable sortable"
 |- style="font-weight:bold; text-align:center; font-family:Arial, Helvetica, sans-serif !important;; background-color:#D81F2B; color:#ffffff;"
@@ Line 171: / Line 174: @@
 [[File:Level 3 badge.png|alt=Level 3 badge|left|frameless|41x41px]]
 |[https://www.epiloglaser.com/ Epilog Laser]
-| 10000 Laser System
+|10000 Laser System
 |<p style="text-align:right;">$5,800</p>
 |yes, and [https://www.epiloglaser.com/assets/downloads/manuals/zing-manual-web.pdf online]
@@ Line 180: / Line 183: @@
 |
 |'''Computer'''
-|HP
+| HP
 |h8-1117c
 |<p style="text-align:right;">$250</p>
@@ Line 212: / Line 215: @@
 ===Hand Tools===
 :<span style="color:#FFFFFF; background:#D81F2B">&nbsp;Laser Area&nbsp;</span> hand tools should be marked with <span style="color:#D81F2B">'''red'''</span> tape or paint.
-:Return all tools to their proper location after use. This rule applies to all areas of our Makerspace.
+: Return all tools to their proper location after use. This rule applies to all areas of our Makerspace.
 ===[[Donations Received]]===
@@ Line 231: / Line 234: @@
 ==Software==
-===Design Software===
+===Design Software ===
 :'''[[Adobe Illustrator Tips|Adobe Illustrator]]''' (Windows 10 and Macintosh)
 :'''[[Adobe Photoshop Tips|Adobe Photoshop]]''' (Windows 10 and Macintosh)
@@ Line 243: / Line 246: @@
 ==Member Showcase==
-===Boss Laser Photo Gallery===
+=== Boss Laser Photo Gallery===
 <gallery>
 File:Wall art closeup.jpg|alt=Wall art closeup|<center>'''4' x 1' Wall art<br>with inlays<br>(by Robbie&nbsp;Cochran)'''</center>