Laser
The Laser Engraver/Cutter Area at Pikes Peak Makerspace (PPM) consists mostly of Level 3 equipment.
Additional training is required to use our Level 3 equipment.
Laser Area hand tools should be marked with red tape or paint.
Safety First
Members must know the following information:
- In case of emergency, call 911.
- Our physical location is:
- 735 East Pikes Peak Avenue
- Colorado Springs, CO 80903
- use this when ordering pizza or an ambulance
PPM Fire Escape Plan
- Fire Escape Plan maps are posted throughout the Makerspace.
- There are 7 fire extinguishers on the fire escape plan map. Review the PPM Fire Escape Plan for locations.
First Aid
- There is a FIRST AID Supply Cabinet in our Kitchen Area.
- FIRST AID Kits are available in four areas: the Kitchen, Metal Shop, Wood Shop and CNC Room.
Eye Wash Stations
- Emergency Eye & Face Wash Stations are mounted in four areas: the Kitchen, Wood Shop, CNC Room and Vented Room.
Personal Protective Equipment (PPE)
- Wear protective equipment in all Wood and Metal Shop Areas.
- Wear gloves when using Isopropyl Alcohol and other cleaners.
Hazardous Chemicals
- All hazardous chemicals must be stored in the yellow hazardous chemical storage cabinet located in the Vented Room.
- Review the Safety Data Sheet (SDS) information of unknown products before use.
- SDS information is available via the QR code on the hazardous chemical storage cabinet or this spreadsheet.
- Do not bring dangerous chemicals to the makerspace.
- Spray paint, stains, and other approved items must be stored in the hazardous chemical storage cabinet in the Vented Room.
- Please DO NOT paint indoors.
Classes and Training
New Member Orientation
Area Captain
- Jonathan Wommack (Epilog Laser)
- View all PPM Area Captains
Area Captain Duties
Classes
- Pikes Peak Makerspace announces its Upcoming events, including classes, on Meetup
Training
- Jonathan Wommack (Epilog Laser)
DO NOT cut materials with PVC on either laser, this will release chlorine gas which is toxic.
- ALWAYS ensure the work area interior and exterior is clean before and after your work.
- The maximum bed size for vector cutting or raster etching is 16” x 12” or less.
Events
For Additional Help
- Use the PPM Slack channel #laser-cutter
The following pages contain historical information. The pages are provided for reference only.
• Introduction to the Zing Laser (15:26, 20 May 2015)
• Laser Cutting Material Table (15:41, 21 May 2015)
• Laser Cutting Acrylic (16:31, 24 November 2015)
Equipment Lists
Zing LASER
Picture | Item | Manufacturer | Model Number |
Estimated Value |
Manual | Owner | Status | Problem Description |
Zing 30 Watt Laser |
Epilog Laser | 10000 Laser System | $5,800 |
yes, and online | PPM | working | ||
Computer | $250 |
N/A | PPM | working | ||||
Monitor, 20" | Dell | 2007FP | $100 |
N/A | PPM | working | ||
Number |
Value |
Description |
Hand Tools
- Laser Area hand tools should be marked with red tape or paint.
- Return all tools to their proper location after use. This rule applies to all areas of our Makerspace.
Donations Received
Wish List
Benefits and Policies
- PPM members enjoy discounts at the following local merchants:
- (walk in, show proof of membership)
Company | Website | Benefit | Directions to |
Woodcraft of Colorado Springs | 10% discount | 4438 Austin Bluffs Parkway | |
CO Lumber Specialties | 10% discount | 3636 Stone Avenue | |
GENERAL AIR | 10% discount | 3031 N Nevada Ave. | |
ACE Hardware Uintah Gardens | 10% discount | 1830 W Uintah Street | |
- Map of stores that provide PPM member discounts
- Map of helpful local resources curated by our makers
- At home LightBurn subscriptions can be purchased at a discounted rate for being a PPM member.
- The discount code is saved as a Pinned Message in our 'laser-cutter' channel in Slack.
Equipment Reservations
Materials
- DO NOT cut materials with PVC on either laser, this will release chlorine gas which is toxic.
- Avoid reflective material.
- Donate for "Wood Sheet for Laser" via PayPal: bit.ly/ppmstuff
- Or, leave donations in a black payment box, or use a QR code.
Red Tags
Scrap and Trash
- Trash day is MONDAY
- Recycling day is MONDAY (96 gallon tote)
- Single Stream Recycling provided by Waste Connections. Paper, cardboard, cans, glass, and one time use plastics.
- Empty recycling and trash into our dumpster at the back (south side) of the building.
- Always leave the space better than you found it.
Software
Design Software
- Adobe Illustrator (Windows 10 and Macintosh)
- Adobe Photoshop (Windows 10 and Macintosh)
- Inkscape (multi-platform)
- Procreate (Tips, Training and Meetups)
Printing Software
- Adobe Acrobat
Member Showcase
Epilog Laser Photo Gallery
- For even more member projects, visit our #showcase channel on Slack, or follow our social media links.
See Also
Laser -- BOSS
Curated Links
- ImagR -- Prepare your image for laser engraving
- Bell Laser - After market parts for laser machines
- Laser Research Optics - Alternative and cheaper sources of lenses
Other Fun Stuff
PPM Tool Color Map — Interactive
Search the PPM Wiki — include both Content pages and Multimedia
Contact Us if you cannot find your answer here on our Wiki or if you notice any info that is outdated.